Skip to content
Request a callbackCallback

For homeowners, builders and small developers

Structural Calculations: What They Include and When Needed

Sviatoslav JerdetchiiCEO & Founder of Craftex. Updated , 5 min read

Hand with a marker drawing where a structural frame meets the ground on a whiteboard sketch

The short answer

Structural calculations are an engineer's written proof that a beam, wall, floor or foundation can carry its loads safely. They show building control that the work meets Part A, the structure part of the Building Regulations.

  1. A set lists the loads, the member chosen and the checks it passes, with a drawing.
  2. You may need them to remove a load-bearing wall, add a floor, extend, convert a loft or underpin.
  3. Beam, padstone and lintel calculations are small sets for one opening.
  4. Our structural engineers write them, and our builders build from them.

Structural calculations are the engineer's proof that part of a building can carry its weight safely. They turn a beam, a wall or a foundation into numbers that building control can check. This guide explains what a set includes, when you need one and how to get it.

Our engineers write structural calculations for homes and larger buildings, and our builders build from them. Has building control asked for calculations? Send us your drawings and we tell you what is needed.

What structural calculations are

Every part of a building carries weight and passes it down to the ground. Calculations follow that weight from the roof to the soil. At each step they show the part chosen is strong enough and stiff enough.

Part A of the Building Regulations sets three rules for structure. A1 says the loads must reach the ground safely, without bending or moving enough to harm the building next door. A2 covers ground movement. A3 says an accident must not cause a collapse out of proportion to its cause.

Approved Document A is the government's guidance on meeting those rules in England. It also lists the design standards engineers use, the Eurocodes. Calculations are where those standards are applied to your building. Our guide to Part A building regulations explains each rule.

What a set of structural calculations includes

A set of calculations reads like a short report. A small job may be a few pages. A building may be a thick file. The parts are the same.

What a set of structural calculations includes
PartWhat it shows
Design basisThe standards used, such as the Eurocodes listed in Approved Document A
LoadsDead loads (the building's own weight), imposed loads (people and furniture) and wind
Load pathHow the weight travels from the roof down to the foundation
Members chosenEach beam, column, joist or lintel, named by type and size
ChecksStrength, bending, and how far each member may deflect, meaning sag
Ends and connectionsBearings, padstones and bolts where members meet walls or each other
FoundationsHow the new load reaches the ground, and any work to the foundations
Drawing or sketchWhere each member goes, so the builder can build it

The drawing matters as much as the numbers. A builder works from the drawing. Building control reads both. Keep both with the house papers: a future buyer's surveyor or lawyer may ask how a wall was taken out.

When you need structural calculations for building regulations

Under the Building Regulations 2010, building work includes extending a building, making a material alteration and underpinning. An alteration is material if it would leave the building failing a rule it met before. Part A, structure, is one of those rules.

So when a job changes how the building carries weight, building control needs to see that Part A is still met. Calculations and drawings are how an engineer shows it.

  1. Removing or opening up a load-bearing wall. The new beam and its supports.
  2. Loft conversions. New floor joists, beams and any change to the roof structure.
  3. Extensions. Foundations, beams over openings and any steel frame.
  4. Basements and underpinning. Walls, floors, foundations and the digging order.
  5. Extra storeys and heavy loads. The structure below must carry the new weight.

GOV.UK lists two main routes. Full plans is the most thorough, with a decision usually within 5 weeks, or 2 months if you agree. A building notice is for smaller projects only and gives no formal approval.

Beam, padstone and lintel calculations

The smallest sets cover one opening in a wall. Each one checks a single part and what it rests on.

Small calculation sets for one opening
CalculationWhat it checks
Beam calculationThe steel or timber beam that replaces a wall or spans a new opening
Padstone calculationThe concrete block under each end of the beam, so the wall below is not crushed
Lintel calculationThe beam over a new or wider window or door

Planning Portal guidance says a new beam should normally have at least 150mm bearing on each side. It adds that a padstone of dense concrete may be needed to spread the load. A steel beam should normally be protected to resist fire for 30 minutes.

Our guide to steel beam and RSJ sizes shows how the engineer picks the beam itself.

Great experience from start to finish. Communication was clear, the workmanship was excellent, and the whole project was managed professionally.

Rhea Langford, Google reviewSee all reviews on Google

How much structural calculations cost

There is no national price list. HomeOwners Alliance, a UK consumer advice website, gives these market ranges in its 2026 guide. We read it on 21 November 2026. They are market figures, not our prices.

Structural engineer fees, market figures (HomeOwners Alliance, 2026)
ServiceMarket range
Calculations for an RSJ£60 to £950
Basic project£350 to £450
Complex projectup to £10,000

The fee depends on how many members need checking, how much is known about the building and whether a site visit is needed. Our structural engineers give you a fixed fee after the first call.

How to get structural calculations from our team

Send us what you have and we tell you what the calculations need to cover. These items save a visit or a second round of questions.

  • Your architect's or builder's drawings, if you have them
  • Photos of the wall, opening or area, and the rooms above
  • The age and type of the building
  • Any notes from building control

Craftex is a team of architects with 50 years of experience, interior designers, engineers and builders.

Our engineers write the calculations and drawings. Our builders build from them, so a question on site is answered inside one team. Our people bring combined team experience of 834 design projects and 561 major construction projects.

Work already done without approval? Our engineers can inspect and write up what is there for regularisation. Whatever stage you are at, send us your drawings and we start with the loads.

Frequently asked questions

Who can do structural calculations?

A structural engineer. Planning Portal guidance says a structural engineer or surveyor can be employed to decide if a wall is load-bearing and then design a beam. Our structural engineers write calculations for homes and larger buildings.

Do I need structural calculations for building regulations?

If the work affects the structure, building control needs to see that it meets Part A. Calculations and drawings are how an engineer shows that. Send us your drawings and we tell you what the job needs.

What are padstone calculations?

They check the wall under each end of a beam. Planning Portal guidance says a padstone of dense concrete may be needed so the wall is not crushed. The engineer sizes it with the beam.

What if the work was done without calculations?

The owner can apply to the council for regularisation. The government's notes on Approved Document A say covered work may need to be exposed, for example to check the size of a steel beam. Our engineers can inspect and write up what is there.

How much do structural calculations cost?

HomeOwners Alliance's 2026 guide gives £60 to £950 for calculations for an RSJ and £350 to £450 for a basic project, as market figures. Our structural engineers give you a fixed fee after the first call.

Refer a project

Earn 5–10% lifetime commission

from the revenue we generate from your introduction.

Architects, agents, developers, business owners: anyone can refer. Introduce a client and we pay you on their first project and every project after it, for as long as they work with us. The rate depends on the project and is agreed in writing before work starts.

Rates and conditions apply. See the referral terms.

Want calculations from the team that will build it?

Our engineers write the calculations and drawings for building control, and our builders carry out the work from them. Send us your drawings. We reply within one hour, Monday to Saturday, 8am to 6pm.

Reply within 1 hour, Mon–Sat 8am–6pm. Urgent? WhatsApp us for a reply straight away, any day.

WhatsApp us